The short answer

10ppm gasoil has no more than 10 milligrams of sulphur in each kilogram of fuel. It is the grade modern diesel engines are built for, and it is what most road diesel markets now ask for. 500ppm gasoil allows up to 50 times more sulphur. It still sells into countries and uses where the rules allow it, such as some inland and off-road markets, generators and older fleets.

So the question is not which grade is better. It is which grade the destination allows and the end user can burn. A buyer who gets that wrong ends up with a cargo that customs will not clear or that damages the engines it is sold to. A seller who blurs the two in an offer is either careless or hoping nobody checks.

What the numbers actually mean

In fuel, ppm means parts per million by mass, so 1 ppm is 1 mg/kg. Offers, specs and certificates switch between ppm, mg/kg and percent, and that is where a lot of confusion starts. The same limits written three ways:

Grade as offeredmg/kg (ppm)% by massWhere you usually see it
10ppm / ULSD100.001%EN590 road diesel, most waterborne diesel trade
15ppm (US)150.0015%ASTM D975 grade S15, US road and off-road diesel
50ppm500.005%Road diesel in many importing countries
500ppm / "Gasoil 0.05%"5000.05%Older or inland road standards, off-road and power use
0.1% gasoil1,0000.1%EU heating gas oil; marine gasoil in emission control areas
D2 / 0.2% gasoil2,0000.2%Older GOST-style offers, industrial use
Unit conversions are exact. The "where you see it" column is a general guide, not a legal list; always check the destination's own standard.

Notice the trap in the fourth row. "Gasoil 0.05%" sounds like a tiny number, but it is 500ppm, fifty times the EN590 limit. If an offer says "low sulphur" without a figure, ask for the figure in mg/kg.

Who buys 10ppm, and why

Low sulphur matters because of what sits in the exhaust of a modern diesel engine. Catalysts and diesel particulate filters are poisoned or clogged by sulphur. The global clean fuels strategy of the Climate and Clean Air Coalition, worked on with the UN Environment Programme, sets 50ppm as the minimum and 10ppm as the goal. Euro 4/IV vehicles and newer are designed around low-sulphur fuel.

That is why the move to low sulphur has been steady. According to the UNEP and Climate and Clean Air Coalition tracker, 115 countries had adopted diesel standards of 50ppm or less by January 2025. In West Africa, ECOWAS ministers set a 50ppm sulphur limit for all imported petrol and diesel from 1 January 2021, with local refineries given until 1 January 2025.

The traded market has moved with it. In January 2018 Platts changed its flagship FOB Singapore and FOB Arab Gulf gasoil assessments from 500ppm to 10ppm, saying waterborne diesel trade was by then mostly 10ppm. A 10ppm cargo can go to almost any market, because it also meets every looser limit. That flexibility is one reason 10ppm is the default grade for large cargoes.

If the buyer needs full EN590, not just 10ppm sulphur, see our EN590 10ppm specification guide. 10ppm is only one of the lines EN590 sets.

Who still buys 500ppm

The same tracker counted 78 countries still using fuels above 50ppm, mostly in parts of Africa, Asia, the Middle East and Latin America. Where the national road standard allows 500ppm, or where the fuel goes to generators, mines, farms, construction plant or older trucks without exhaust after-treatment, 500ppm gasoil can still be the right product and is often the cheaper one.

It also still has its own price lines. Platts kept separate "Gasoil 0.05%" (500ppm) assessments in Singapore and the Arab Gulf after the 2018 change, and publishes 500ppm and 10ppm grades on an FOB Fujairah basis. In the US, ASTM D975 still lists an S500 grade next to S15. So 500ppm is not a fake or obsolete product. It is a narrower one, and the buyer has to be sure the destination accepts it.

Before agreeing a 500ppm deal, check three things: the import standard at the discharge country (it may have tightened since the last cargo), the end use (a modern truck fleet needs low sulphur even where 500ppm is legal), and whether the cargo will be re-exported or trucked across a border with a stricter limit.

Side by side

10ppm gasoil500ppm gasoil
Sulphur limit10 mg/kg max500 mg/kg max (0.05%)
EnginesModern diesel with catalysts and particle filters, plus all older enginesOlder engines and equipment without after-treatment
MarketsAlmost all road diesel markets; meets any looser limitOnly where the national standard or the end use allows it
Typical price referencePlatts / Argus 10ppm gasoil or diesel lines for the loading regionSeparate 500ppm ("Gasoil 0.05%") lines where they exist
Sulphur test (examples)EN ISO 20846 or 20884 (EN590); ASTM D5453 for US S15ASTM D2622 or D5453; ISO XRF methods
Biggest risk for the buyerContamination in tanks or lines lifting it off-specCargo not accepted at destination, or sold on as low sulphur
General comparison for buyers. The exact limits and test methods for a deal are the ones written into the SPA.

We do not publish prices or spreads between the two grades. For how a contract ties a cargo to a published price line, see our Platts and Argus benchmarks guide. The key point is that a 10ppm cargo priced against a 500ppm line, or the other way round, is a mismatch worth questioning before signing.

How sulphur is tested, and why it matters

Measuring 10 mg/kg is harder than measuring 500 mg/kg, so the standards name specific methods. EN590 lists EN ISO 20846 (ultraviolet fluorescence), EN ISO 20884 (wavelength-dispersive X-ray fluorescence) and EN ISO 13032 (energy-dispersive X-ray fluorescence, which in its 2024 edition covers diesel from 5 to about 60 mg/kg). In the US, ASTM D975 uses D5453 as the referee method for S15 and D2622 for S500 and S5000.

What this means in practice: when you read a certificate of quality or an inspector's report for a 10ppm cargo, the sulphur line should name a method that is fit for that level. A sulphur result of "<10" with no method, or a method meant for much higher sulphur levels, is a reason to ask questions. Our guide on how to verify an SGS or Intertek report explains how to check that the report itself is genuine.

Why a 10ppm cargo can arrive off-spec

Ten milligrams per kilogram leaves very little room. A simple sum shows it: mix 99 tonnes of 10ppm gasoil with just 1 tonne of 500ppm and the blend comes out at about 14.9ppm, already over the EN590 limit. That is why shared lines, tanks that held a higher-sulphur product, and ship tanks with leftover cargo are real risks for 10ppm.

  • Ask for the tank's previous cargo and how it was cleaned, especially in a tank-to-tank transfer. Our TTT, TTO and TTV guide covers how those transfers work.
  • Agree in the SPA where quality is measured (shore tank, ship's tanks after loading, or at discharge) and which result counts if they differ.
  • Ask the inspector for first-foot or line samples on a sensitive 10ppm loading, not only a final composite.
  • Keep the sealed retained samples until the cargo is accepted.

Red flags in gasoil offers

  • "10ppm or 500ppm, same price." They are different products with different price lines. A seller who does not care which one you want may not have either.
  • The sulphur grade changes between papers. The offer says 10ppm, the FCO says 50ppm and the spec sheet says 0.05%. Ask which one the seller will guarantee in the SPA.
  • "Low sulphur" with no number. Ask for the limit in mg/kg and the test method.
  • A certificate that shows a result but no method, or a 10ppm result tested with a method meant for much higher levels.
  • EN590 named on a 500ppm cargo, or D2 sold as EN590. Our EN590 seller check guide and trading scams guide cover the wider paper trail.
  • No named load port, terminal or tank. A real cargo of either grade sits somewhere specific.

Common questions

What is the difference between 10ppm and 500ppm gasoil? The sulphur limit. 10ppm gasoil has at most 10 mg of sulphur per kg of fuel; 500ppm gasoil allows up to 500 mg/kg, which is 0.05% by mass. The lower figure is needed by modern diesel engines with catalysts and particle filters.

Is 10ppm gasoil the same as EN590? Not automatically. 10ppm describes only the sulphur limit. EN590 also sets cetane, density, flash point, cold flow, distillation and other limits, so a 10ppm cargo may or may not meet the full EN590 spec.

Is "Gasoil 0.05%" the same as 500ppm? Yes. 0.05% by mass equals 500 mg/kg. Platts uses the name "Gasoil 0.05%" for its 500ppm assessments in Singapore and the Arab Gulf.

Can 500ppm gasoil be blended down to 10ppm? Not in any practical way by mixing. Sulphur is removed at the refinery by hydrotreating. Blending only moves sulphur around, and even a small amount of 500ppm can push a 10ppm cargo off-spec.

Which grade should I buy? The one the discharge country's standard allows and the end user's engines need. If the fuel goes to modern trucks or might cross into a stricter market, 10ppm is the safer choice. Check the national standard before you agree the deal.

Can I post either grade on TradeNexusMarket? Yes. Members post gasoil requirements and offers, and we ask them to state the sulphur grade in mg/kg. We do not publish prices, and we do not claim stock we have not seen; proof of product is checked before a Deal Room opens.

Buying or selling gasoil on TradeNexusMarket

Posting a requirement or an offer is free. Name the sulphur grade in mg/kg, the spec it should meet and the delivery port, so a match starts on the same basis. Before a Deal Room opens, a person on our team checks company papers and at least one proof of product, and members are screened against sanctions lists. Contacts stay masked until a match is approved.

Inside the room, stages run in order: signed SPA, inspection, payment instrument, then shipment. The full sequence is in our Deal Room rules.

See our gasoil D2 and AGO page and our EN590 10ppm diesel page, browse the public board, or create a free account to post a requirement.

General information only, not legal or technical advice. Fuel standards change; confirm the current limit with the destination country's standards body and your inspector before you sign.

Post free, trade with checked companies

TradeNexusMarket is a B2B marketplace for EN590, Jet A-1, LPG, LNG, crude oil and other fuels. Posting is free and needs no documents. Contacts stay masked, our team makes the match, and both companies are checked before the Deal Room opens. Commission is charged only on a closed deal.

Open a free account No documents to sign up. Commission only on a closed deal.

Related reading