Guide · EN590
The EN590 10ppm specification explained, line by line
The TradeNexusMarket team · · Updated · 10 min read
What EN 590 is
EN 590 is the European standard for automotive diesel, published by CEN, the European standards body. It has been revised several times. The current edition is EN 590:2025, which CEN published at the end of July 2025 and which replaced EN 590:2022. National standards bodies had until January 2026 to adopt it; in Germany, for example, it appeared as DIN EN 590:2025-09, replacing the 2022 version. Many countries outside Europe use EN 590 as their national diesel spec or copy its main limits, which is why EN590 is the grade most often quoted in international offers.
"10ppm" refers to the sulphur limit: no more than 10 mg of sulphur per kg of fuel. That is why EN590 is also called ultra-low sulphur diesel (ULSD). Strictly speaking, all EN590 is 10ppm, so "EN590 10ppm" is a little redundant, but it is the name the market uses.
A certificate of quality (CoQ) for a real cargo lists each property, the test method (usually an EN ISO or ASTM method), the limit and the measured result. If a sheet shows only limits and no results, it is a spec, not a test. A good CoQ also says which edition of EN 590 the product was tested against.
What changed in EN 590:2025
Most limits are the same as in the 2022 edition. The changes a buyer is likely to notice on paper are these:
- Lower minimum density for summer grades. EN 590:2022 had already cut the minimum density for the colder temperate grades D, E and F to 815 kg/m³. EN 590:2025 does the same for grades A, B and C, so every temperate grade is now 815.0 to 845.0 kg/m³. A result of, say, 817 kg/m³ is inside the 2025 limit for a summer grade, but it would have failed the 2022 summer grades.
- A new particle count limit. No more than 10,000 particles per millilitre of 4 µm or larger, applied at what the standard calls the point of particle certification and measured with IP 630 (procedure A or B). A new Annex A explains the requirement. It follows the 2022 edition's attention to hard particles that wear fuel injection equipment.
- An extra viscosity method. The constant pressure viscometer method, EN ISO 18335, is now accepted as an alternative to EN ISO 3104.
For a buyer this mostly means one thing: write the edition into the SPA. "EN590 10ppm" on its own does not say whether the 2022 or 2025 limits apply, and the density and particle count lines differ between them. A CoQ that quotes the 2013 or 2022 edition is not wrong by itself, since the cargo may have been tested before the new edition was adopted, but it should match what your contract and your destination market require. Where a cargo is meant to carry a particle count, ask the inspector or the seller where in the supply chain it was certified rather than assuming.
The main properties and their limits
| Property | EN 590:2025 limit | Why a buyer cares |
|---|---|---|
| Sulphur | 10 mg/kg max | Required for modern engines and exhaust after-treatment. Also the basis of most import rules. |
| Cetane number | 51.0 min | How readily the fuel ignites. Low cetane means hard starts, noise and smoke. |
| Cetane index | 46.0 min | A calculated figure from density and distillation. A cross-check on the cetane number. |
| Density at 15 °C | 815.0 to 845.0 kg/m³ (temperate grades A to F) | Affects energy per litre and the conversion between volume and weight on the invoice. The minimum was 820.0 for grades A to C before 2025. |
| Flash point | Above 55 °C | A safety property for storage and transport. |
| Polycyclic aromatics | 8.0% (m/m) max | Linked to soot and emissions. |
| FAME (biodiesel) content | 7.0% (v/v) max | Some markets need FAME-free diesel. Check the figure against your own rules. |
| Water | 200 mg/kg (0.020% m/m) max | Water causes corrosion and microbial growth in tanks. |
| Ash | 0.010% (m/m) max | Mineral residue that can damage injectors and after-treatment. |
| Lubricity (HFRR at 60 °C) | 460 µm max | Low-sulphur fuel loses natural lubricity. This protects injection pumps. |
| Viscosity at 40 °C | 2.0 to 4.5 mm²/s | Affects spray pattern and pump wear. |
| Distillation | Less than 65% recovered at 250 °C; at least 85% at 350 °C; 95% recovered by 360 °C | Shows the fuel is in the diesel boiling range and not cut with lighter or heavier product. |
| Total contamination | 24 mg/kg max | Particles that block filters. |
| Particle count (≥ 4 µm) | 10,000 per mL max at the point of particle certification (new in 2025) | Hard particles wear injection equipment even when total contamination is within limits. |
| Oxidation stability | 25 g/m³ max, plus 20 h min when FAME is above 2% | How well the fuel keeps in storage. |
Cold weather: CFPP and climate grades
Diesel thickens and forms wax crystals when it gets cold. The cold filter plugging point (CFPP) is the temperature at which the fuel stops passing through a standard filter. EN 590 does not set one CFPP for everyone. It defines grades, and each country picks the grade for each season in its national annex.
Temperate grades run from Grade A (CFPP +5 °C max) through B (0 °C), C (−5 °C), D (−10 °C), E (−15 °C) to F (−20 °C). There are also arctic classes for very cold climates, with lower CFPP and different density and viscosity limits.
In practice this means a cargo offered as "EN590 10ppm" without a grade is not fully described. A buyer in the Gulf may be happy with summer diesel. A buyer in Eastern Europe in January is not. Ask for the grade or the CFPP figure, and write it into the SPA next to the edition of the standard.
Matching the spec to the hub
Where the diesel sits changes which questions matter most.
- Rotterdam and ARA. Product here often moves on by barge or coaster into markets that buy to EN 590 with seasonal grades, so the climate grade and CFPP need to fit the destination and the month of delivery. Our EN590 Rotterdam page covers how barges, TTT transfers and inspection work at the hub.
- Fujairah. The regional price assessments are for gasoil with a maximum of 10ppm sulphur. Some 10ppm gasoil meets the whole of EN 590 and some does not, so "10ppm" in an offer is not proof of EN590. The inspector's certificate against each EN 590 line settles it. Our EN590 Fujairah page explains storage, transfers and origin checks there.
- Singapore. The Platts benchmark here is also for 10ppm gasoil, and many of the Asia-Pacific markets supplied from Singapore set their own national diesel standards, so a 10ppm cargo there may have been made for a buyer who never asked for EN 590. Read the certificate against the EN 590 limits, not the sulphur figure alone. Our EN590 Singapore page covers the Jurong Island terminals, MOPS pricing and how transfers work.
Numbers that should make you ask questions
Real test results have decimals and small variations. Sheets that were typed instead of tested tend to give themselves away. Things our team looks at:
- Every result sits exactly on the limit, for example sulphur 10.0, density 845.0, cetane 51.0. Real refinery output usually has some margin.
- A sulphur result of 0 or a figure below what the test method can measure.
- Density and cetane index that do not fit together. Cetane index is calculated from density and distillation, so a mismatch suggests the numbers were made up separately.
- Test methods missing or wrong, such as a method for petrol listed against a diesel property.
- No edition of the standard, or limits copied from one edition while the header cites another.
- An old date, or no sample reference. A certificate should name the tank or vessel, the sample date and the laboratory. If a tank storage receipt (TSR) is offered as proof of product, the CoQ and the TSR should point to the same terminal, tank and product.
- The same certificate used for different cargoes. Fake offers often recycle one genuine document with a changed date or quantity.
If something looks off, check the report with the inspection company's local office using contact details from its own website, not the ones on the document. Our 10-point seller checklist covers the company, the tank and the paperwork.
EN590 vs D2 gas oil, ULSD and other names
Offers often mix EN590 with other names. They are not the same product.
- D2 gas oil is a loose trade name, mostly used in offers for gas oil made to Russian or former-Soviet GOST standards. It usually allows much more sulphur than 10 mg/kg and is not road diesel in Europe. A seller offering "D2 or EN590, same price" is treating two different products as one, which is a warning sign by itself. See our Gasoil D2 page for how that grade is traded. Its heavy cousin "D6" is just as informal; see what D6 virgin fuel oil really is.
- ULSD (ultra-low sulphur diesel) describes the sulphur level. In the US, ULSD is made to ASTM D975 with a 15 ppm sulphur limit, so US ULSD and EN590 are close but not identical. Our Houston and US Gulf Coast hub sets the two standards side by side and explains how EN590-spec export cargoes are made there.
- Gasoil 0.1% or 50ppm are higher-sulphur grades used for heating, marine or off-road use in some markets. Prices and import rules differ. Our gasoil 10ppm vs 500ppm guide sets the sulphur grades side by side and explains who buys which.
If the offer and the spec sheet use different names, ask the seller which standard the product was tested against and get a certificate that says so.
Sanctions: GOST-spec gas oil is often Russian-origin or Russian-route product. We cover it as information only. Depending on your company, bank, insurer and destination, EU, UK and US sanctions and the G7 price cap can prohibit or limit dealing in it. Ask for the certificate of origin early and take your own compliance advice before you sign.
Who tests the product, and when
The spec sheet in an offer is the seller's claim. What protects the buyer is an independent inspection at loading or at transfer, by an inspector such as SGS or Intertek, against the spec written into the SPA. The contract should name the inspector, the place, the test methods, the edition of EN 590 and who pays.
In a tank-to-tank deal, the buyer's inspector usually samples the seller's tank before the transfer and the receiving tank after it, and the receiving terminal may test again. Our guide to TTT vs TTO vs TTV explains how each transfer is checked.
A good quality result in the seller's tank is not a reason to pay early. A sample proves what is in the tank, not who owns it or whether it will be handed over. That is why "MT103 after dip test" is a warning sign: the spec passes, the money goes, and the transfer never happens.
Many buyers also test on arrival. If results differ, the SPA should say whose result counts and how disputes are settled.
Common questions
Is 10ppm gasoil the same as EN590? Not automatically. 10ppm describes the sulphur limit only. EN590 also has to meet the cetane, density, flash point, cold-flow, distillation and other limits in EN 590.
Which edition of EN 590 should the SPA name? The one your destination market and your own buyers require, written out in full, for example "EN 590:2025, Grade C". If the seller's CoQ cites an older edition, agree in writing which limits apply.
Is a density of 817 kg/m³ off-spec? Under EN 590:2025 it is inside the limit for every temperate grade. Under the 2022 edition it was below the minimum for summer grades A to C. That is one more reason to name the edition.
Does an EN590 cargo need a particle count result? EN 590:2025 sets the limit at the point of particle certification. Ask your inspector where that point falls for your cargo and whether the result should appear on the certificate.
Using the spec in a TradeNexusMarket deal
On our EN590 10ppm diesel page the typical spec is shown as a reference. Before an EN590 seller on TradeNexusMarket enters a Deal Room, it shows our team a proof of product, which can be a recent inspection report. Once in the room, the buyer and seller agree the exact spec, edition, grade and inspection. No fees are collected for documents or tests, and the full rules are on our Deal Room rules page.
Looking for EN590 now? See the current posts on the market board, or create a free account and post your own requirement with the grade and edition you need.
Limits summarised from EN 590:2025 for general information. The standard itself is the reference for any contract.
Post free, trade with checked companies
TradeNexusMarket is a B2B marketplace for EN590, Jet A-1, LPG, LNG, crude oil and other fuels. Posting is free and needs no documents. Contacts stay masked, our team makes the match, and both companies are checked before the Deal Room opens. Commission is charged only on a closed deal.
Related reading
- Guide · ProductsGasoil 10ppm vs 500ppm: what the sulphur grade means and who buys which
- Guide · EN590How to check whether an EN590 seller is real: a 10-point checklist
- Guide · Deal documentsWhat a TSR (tank storage receipt) is, and how to check one
- Guide · Pricing referencesPlatts and Argus benchmarks explained: CIF NWE, FOB Singapore and FOB Arab Gulf
- Guide · Deal structuresTTT vs TTO vs TTV: how diesel actually changes hands at a terminal
- Guide · Red flagsWhy "MT103 after dip test" is a warning sign in fuel offers